Jog multiple axiis

If you think you've found a bug post it here.

Re: Jog multiple axiis

Postby Zed_UCCNC » Sat Jun 27, 2020 9:41 pm

I think that the problem goes away when I disable backlash compansation.
But I need backlash compensation!
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby Zed_UCCNC » Tue Jun 30, 2020 3:05 pm

cncdrive wrote:OK, my collegue Dezsoe will check it out.

WITH BACKLASH ENABLED
In this video look at the DRO's and stepper between 13 and 24 seconds, the function is normal.
https://youtu.be/NvFRs0yB67o
https://youtu.be/NvFRs0yB67o

During the other part of the video, the input at the keyboard is constant direction for 4 steps BUT the stepper direction of rotation alternates, look at the DRO's, the readout is not normal.

I think this makes jogging to an edge unreliable ( with BL enabled)
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby Zed_UCCNC » Sat Dec 05, 2020 10:34 pm

Is there any news on this?
Was a bug found? Repaired?
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby Zed_UCCNC » Tue Dec 22, 2020 4:26 pm

This problem is also present in Version1.2113 (my previous reports were on version 1.2112 and 1.2111)
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby Zed_UCCNC » Thu Jan 14, 2021 1:35 pm

cncdrive wrote:OK, my collegue Dezsoe will check it out.

Is there any progress on this issue?

I now have the same issue on an AXBB-E, previous problems were on a UC100
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby Zed_UCCNC » Tue Mar 02, 2021 2:16 pm

Is there any progress on this issue?
After 8 months I think it is reasonable to expect the developers to do or say something substantive?
Has any investigation been done?
Is there any plan to fix or patch it?

This is an impediment to accuracy and efficiency.
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby cncdrive » Tue Mar 02, 2021 5:52 pm

Dezsoe, did you test this report?
Could you reproduce the problem?
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: Jog multiple axiis

Postby dezsoe » Wed Mar 03, 2021 12:56 pm

I'll have to test it again, it was so long ago. I'll be back with the results.
dezsoe
 
Posts: 2049
Joined: Sun Mar 12, 2017 4:41 pm
Location: Csörög, Hungary

Re: Jog multiple axiis

Postby Zed_UCCNC » Tue Mar 09, 2021 12:59 pm

dezsoe wrote:I'll have to test it again, it was so long ago. I'll be back with the results.

dezsoe: do you have any results?
Zed_UCCNC
 
Posts: 37
Joined: Wed Jun 24, 2020 1:15 pm

Re: Jog multiple axiis

Postby dezsoe » Tue Mar 09, 2021 1:53 pm

Yes. I can confirm that with UC100 and with your profile I can reproduce the problem. First I need to change to step jog mode, then jog all axes at least once. After this if I jog any axis then the other two will also move.
dezsoe
 
Posts: 2049
Joined: Sun Mar 12, 2017 4:41 pm
Location: Csörög, Hungary

PreviousNext

Return to Report a bug

Who is online

Users browsing this forum: No registered users and 1 guest