I have recently ordered a bulkman3D UltimateBee Kit with UC300 and IHSV57 Servos. I also purchased an AXBB-E controller due to some of the bad reviews about the UC300. I have wired up everything and the servo has a green blinking light it will not move at all. I have wired the servo just like I would a stepper and the only thing I get is green blinking light.
I decided to remove all other wiring and motors and connected only one servo and still can not get anywhere. I got PUL+ wired to O9 and Dir+ wired to O10, the axis is enabled. Negative wire for each is going to -5v. I also tried wiring the ENA+ to O11 and set that in UCCNC and it made no difference.
Any help would be greatly appreciated.
IHSV57 AXBB
6 posts
• Page 1 of 1
Re: IHSV57 AXBB
by fsli » Thu Nov 10, 2022 12:32 am
bearr wrote:I got PUL+ wired to O9 and Dir+ wired to O10, the axis is enabled. Negative wire for each is going to -5v.
You have that backwards. On the AXBB, the output ports are the ground side. You need to connect O9 to Pul- and O10 to Dir-, and connect +5v to the Pul+ and Dir+ terminals. You can leave Ena+ and Ena- disconnected.
Frank
- fsli
- Posts: 95
- Joined: Mon Jul 11, 2022 12:36 am
Re: IHSV57 AXBB
by dezsoe » Thu Nov 10, 2022 6:34 am
No, Frank, that's not true. Only the O1 to O8 are open collector outputs, the O9 to O17 are pulled up or down, so you can use both 5V0 and 5V+ as common.
The IHSV57 manual does not mention that the power LED is flashing, but I checked some videos and it seems to be normal.
(In the last few days it's the second time I see "that" UC300. It's a nice job, they even used the CNCdrive logo in their manual. Not perfect on all pages, but they tried to do their best.)
The IHSV57 manual does not mention that the power LED is flashing, but I checked some videos and it seems to be normal.
(In the last few days it's the second time I see "that" UC300. It's a nice job, they even used the CNCdrive logo in their manual. Not perfect on all pages, but they tried to do their best.)
- dezsoe
- Posts: 2079
- Joined: Sun Mar 12, 2017 4:41 pm
- Location: Csörög, Hungary
Re: IHSV57 AXBB
by fsli » Thu Nov 10, 2022 11:59 am
dezsoe wrote:No, Frank, that's not true. Only the O1 to O8 are open collector outputs, the O9 to O17 are pulled up or down, so you can use both 5V0 and 5V+ as common.
Okay, my mistake.
Frank
- fsli
- Posts: 95
- Joined: Mon Jul 11, 2022 12:36 am
Re: IHSV57 AXBB
by ger21 » Thu Nov 10, 2022 1:09 pm
due to some of the bad reviews about the UC300.
This is not CNC Drive's UC300ETH, which is excellent, but a chinese controller with the same name. FYI.
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
- ger21
- Posts: 2680
- Joined: Sat Sep 03, 2016 2:17 am
Re: IHSV57 AXBB
by Dazp1976 » Thu Nov 10, 2022 11:36 pm
ger21 wrote:due to some of the bad reviews about the UC300.
This is not CNC Drive's UC300ETH, which is excellent, but a chinese controller with the same name. FYI.
Ahh. That Novosun, Digital Dream, black box thing.
Makes sense now.
- Dazp1976
- Posts: 162
- Joined: Wed Mar 16, 2022 12:57 pm
6 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 1 guest