If you have a question about the software please ask it here.
-
- UCR201: 1-15 selection if you hold Home + Goto Zero
by Matt » Fri Mar 29, 2024 3:34 pm
- 0 Replies
- 1 Views
- Last post by Matt
Fri Mar 29, 2024 3:34 pm
-
- rotate functin g68 to work on an edge
by Battwell » Fri Mar 29, 2024 9:41 am
- 1 Replies
- 11 Views
- Last post by Battwell
Fri Mar 29, 2024 9:53 am
-
- MPG conflict with UCR201 and MPG manual wheel
by giooff » Thu Mar 28, 2024 10:17 pm
- 0 Replies
- 22 Views
- Last post by giooff
Thu Mar 28, 2024 10:17 pm
-
- Possible reasons of gradual Y axis drift?
by aethersis » Sun Mar 17, 2024 4:07 pm
- 5 Replies
- 380 Views
- Last post by formantjim
Mon Mar 25, 2024 2:37 pm
-
- Torch controller
by Fuellagoon » Sun Mar 17, 2024 8:50 am
- 1 Replies
- 119 Views
- Last post by cncdrive
Sun Mar 17, 2024 3:20 pm
-
- Problems Tolerance
by Didi » Tue Mar 12, 2024 12:44 am
- 3 Replies
- 249 Views
- Last post by Didi
Tue Mar 12, 2024 5:55 pm
-
- Continuous motion with multiple movements?
by Anthoval » Thu Mar 07, 2024 12:07 pm
- 1 Replies
- 203 Views
- Last post by ger21
Thu Mar 07, 2024 12:27 pm
-
- UCCNC 1.1027 Works but 1.2113/6 don't
by ryana14 » Wed Mar 06, 2024 2:12 am
- 2 Replies
- 210 Views
- Last post by ryana14
Thu Mar 07, 2024 2:20 am
-
- Problems with Z direction of travel
by Grahamd666 » Sun Mar 03, 2024 5:39 pm
- 6 Replies
- 319 Views
- Last post by dezsoe
Mon Mar 04, 2024 2:19 pm
-
- How to save home position after restart UCCNC?
by sn4k3 » Wed May 13, 2020 11:24 pm
- 25 Replies
- 22631 Views
- Last post by Riyan17
Sat Mar 02, 2024 3:42 pm
-
- Macbook & UCCNC
by philcam » Sun Feb 25, 2024 10:31 am
- 1 Replies
- 273 Views
- Last post by cncdrive
Sun Feb 25, 2024 1:16 pm
-
- Plugin DLL Defective.Rload
by Louie F » Thu Feb 22, 2024 9:24 pm
- 3 Replies
- 297 Views
- Last post by Louie F
Fri Feb 23, 2024 9:15 pm
-
- Appcrash UCCNC 1.2112 and 1.2113
by Dhobbs » Mon Jun 22, 2020 11:23 am
- 3 Replies
- 2760 Views
- Last post by cncdrive
Thu Feb 22, 2024 8:30 pm
-
- Ext. E-Stop triggered
by Mudden » Fri Nov 24, 2023 8:46 am
- 25 Replies
- 5324 Views
- Last post by cncdrive
Wed Feb 21, 2024 9:56 pm
-
- Issue connecting to UC400ETH
by bazzer » Tue Feb 20, 2024 10:49 am
- 3 Replies
- 298 Views
- Last post by bazzer
Tue Feb 20, 2024 11:39 am
-
- 1.2116 update
by ejg3855 » Sun Feb 18, 2024 1:09 am
- 7 Replies
- 578 Views
- Last post by dezsoe
Mon Feb 19, 2024 8:32 pm
-
- Axis setup defaults
by Hammerle5 » Sun Feb 18, 2024 9:16 pm
- 1 Replies
- 231 Views
- Last post by ger21
Mon Feb 19, 2024 12:12 am
-
- Values not being accepted/applied
by kevin » Fri Feb 16, 2024 2:59 pm
- 3 Replies
- 304 Views
- Last post by cncdrive
Sat Feb 17, 2024 6:22 pm
-
- Wiring of AXBB-E and DELTA ASD-B3 servo drive
by fdeporte » Sun Feb 11, 2024 6:31 pm
- 6 Replies
- 685 Views
- Last post by cncdrive
Sat Feb 17, 2024 6:49 am
-
- Need Help - How to back off XYZ during Homing
by sidney7491 » Thu Feb 15, 2024 2:16 am
- 4 Replies
- 376 Views
- Last post by sidney7491
Fri Feb 16, 2024 12:13 am
-
- I need to configure the axis movement AXBB and UCCNC
by KernelCNC » Mon Feb 12, 2024 8:44 pm
- 1 Replies
- 344 Views
- Last post by cncdrive
Wed Feb 14, 2024 4:57 pm
-
- Increase console verbosity eg. "Limit switch X triggered"
by Matt » Fri Feb 09, 2024 6:56 pm
- 2 Replies
- 378 Views
- Last post by Matt
Fri Feb 09, 2024 8:54 pm
-
- UCCNC Loses connection instantly.
by Oakfield » Fri Feb 09, 2024 11:08 am
- 2 Replies
- 343 Views
- Last post by Oakfield
Fri Feb 09, 2024 4:53 pm
-
- Can't get ELP1000Z drives to enable servo's
by Smokie555 » Sun Feb 04, 2024 9:53 pm
- 0 Replies
- 431 Views
- Last post by Smokie555
Sun Feb 04, 2024 9:53 pm
-
- Spindle RPM calibration
by aethersis » Mon Jan 29, 2024 12:07 pm
- 3 Replies
- 690 Views
- Last post by aethersis
Sun Feb 04, 2024 8:21 pm
Return to Board index
Who is online
Users browsing this forum: No registered users and 18 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum