If you have a question about the software please ask it here.
-
- Exception thrown by M31 macro
by DavidT » Mon Sep 30, 2024 9:34 pm
- 1 Replies
- 522 Views
- Last post by cncdrive
Tue Oct 01, 2024 6:50 pm
-
- Lichuan AC 5 Series Servos to AXBB-E wiring
by Phil1322 » Wed Sep 25, 2024 6:35 am
- 8 Replies
- 836 Views
- Last post by Phil1322
Tue Oct 01, 2024 3:05 pm
-
- Two Quick Macro Questions...
by evanevery » Tue Oct 01, 2024 2:34 pm
- 0 Replies
- 162 Views
- Last post by evanevery
Tue Oct 01, 2024 2:34 pm
-
- UCSB - HY02D223B 2.2kw Spindle will not turn on
by CutMeSomeWood » Sat Sep 28, 2024 9:04 pm
- 1 Replies
- 260 Views
- Last post by cncdrive
Sun Sep 29, 2024 8:50 pm
-
- spindle will not reverse direction after rigid tapping cycle
by craig » Sat Sep 28, 2024 11:20 pm
- 3 Replies
- 934 Views
- Last post by cncdrive
Sun Sep 29, 2024 8:45 pm
-
- Error macro 31
by Kenennis » Sun Sep 22, 2024 9:42 am
- 0 Replies
- 766 Views
- Last post by Kenennis
Sun Sep 22, 2024 9:42 am
-
- Accuracy different on same part
by waynesmith880 » Sat Sep 21, 2024 1:17 pm
- 0 Replies
- 771 Views
- Last post by waynesmith880
Sat Sep 21, 2024 1:17 pm
-
- How to Assign a Hotkey to Run a G-code Macro
by taawad » Fri Sep 20, 2024 3:30 pm
- 1 Replies
- 696 Views
- Last post by Battwell
Sat Sep 21, 2024 1:13 pm
-
- UC400Eth not visible over Wifi
by onetimeasker » Wed Sep 18, 2024 7:51 pm
- 2 Replies
- 2162 Views
- Last post by onetimeasker
Thu Sep 19, 2024 7:41 pm
-
- V-Carving Problem
by alen444 » Mon Sep 16, 2024 5:16 pm
- 4 Replies
- 2255 Views
- Last post by cncdrive
Wed Sep 18, 2024 9:05 pm
-
- UC400Eth not visible over Wifi
by onetimeasker » Wed Sep 18, 2024 7:48 pm
- 0 Replies
- 1956 Views
- Last post by onetimeasker
Wed Sep 18, 2024 7:48 pm
-
- Denford Triac converted to UCCNC
by Jonesdp » Mon Sep 09, 2024 3:12 pm
- 0 Replies
- 5590 Views
- Last post by Jonesdp
Mon Sep 09, 2024 3:12 pm
-
- UC400ETH vanished from network
by pbft » Tue Sep 03, 2024 12:01 pm
- 3 Replies
- 1127 Views
- Last post by cncdrive
Wed Sep 04, 2024 7:17 pm
-
- DG4S wiring common gnd vs common positive in controller
by markkunis » Mon Sep 02, 2024 4:13 pm
- 1 Replies
- 851 Views
- Last post by cncdrive
Mon Sep 02, 2024 10:04 pm
-
- Braking Resistor - DC Spindle Motor Setup
by FabianT » Wed Aug 28, 2024 8:54 pm
- 4 Replies
- 827 Views
- Last post by cncdrive
Thu Aug 29, 2024 1:02 pm
-
- Issues with post processor.
by Delco » Sun May 28, 2023 11:40 pm
- 7 Replies
- 3429 Views
- Last post by cncdrive
Thu Aug 29, 2024 11:38 am
-
- AXBBE suddenly doesn't send signal to spindle driver/cooler
by bvanbiezen » Mon Aug 26, 2024 9:04 pm
- 2 Replies
- 815 Views
- Last post by bvanbiezen
Wed Aug 28, 2024 8:01 pm
-
- UCCNC version 1.2117 download link
by Speedhound » Wed Aug 28, 2024 12:44 pm
- 2 Replies
- 1056 Views
- Last post by Speedhound
Wed Aug 28, 2024 3:49 pm
-
- The definitive semi-automatic toolchange setup thread
by qldsteve » Tue Nov 15, 2022 9:42 am
- 10 Replies
- 7832 Views
- Last post by evanevery
Fri Aug 23, 2024 12:14 am
-
- wiring 2 wire nc proximity sensor
by jc1 » Wed Aug 21, 2024 1:10 pm
- 0 Replies
- 2810 Views
- Last post by jc1
Wed Aug 21, 2024 1:10 pm
-
- floor math command
by Battwell » Sat Aug 17, 2024 1:28 pm
- 0 Replies
- 3230 Views
- Last post by Battwell
Sat Aug 17, 2024 1:28 pm
-
- Zero of Z axis changes with Fusion360
by CHM » Thu Aug 08, 2024 7:58 am
- 3 Replies
- 1143 Views
- Last post by CHM
Fri Aug 16, 2024 9:53 am
-
- AXIS MOVEMENT
by MVPAWARDS » Thu Aug 01, 2024 6:25 pm
- 3 Replies
- 1613 Views
- Last post by MVPAWARDS
Thu Aug 08, 2024 12:04 am
-
- Coolant on/off on Rapids
by alex_s » Sat Dec 30, 2017 12:03 am
- 13 Replies
- 25372 Views
- Last post by adamscncmachine
Wed Jul 31, 2024 1:42 am
-
- PowerMill postprocessor
by aethersis » Fri Jul 26, 2024 7:54 am
- 0 Replies
- 3518 Views
- Last post by aethersis
Fri Jul 26, 2024 7:54 am
Return to Board index
Who is online
Users browsing this forum: Majestic-12 [Bot] and 24 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum