General discussion about the UCCNC software
-
- Announcements
- Replies
- Views
- Last post
-
- New USB drivers for UC100
by cncdrive » Tue Mar 04, 2025 4:14 pm
- 6 Replies
- 3864 Views
- Last post by dmanley2000
Tue Mar 18, 2025 2:10 pm
- New USB drivers for UC100
-
- Topics
- Replies
- Views
- Last post
-
- !!!Fake UC100 controllers on e-bay!!!
1, 2, 3, 4, 5 by cncdrive » Mon Oct 17, 2016 7:04 am
- 46 Replies
- 305284 Views
- Last post by HarryPotter69
Fri Feb 02, 2024 2:03 pm
- !!!Fake UC100 controllers on e-bay!!!
-
- Cycle check homes
by Hersheane » Tue Mar 18, 2025 1:14 am - 1 Replies
- 216 Views
- Last post by cncdrive
Tue Mar 18, 2025 2:31 am
- Cycle check homes
-
- Plunge setting
by BJB » Fri Mar 14, 2025 6:28 pm - 2 Replies
- 594 Views
- Last post by BJB
Fri Mar 14, 2025 8:29 pm
- Plunge setting
-
- UCCNC - Software update or new version
1, 2by deancnc » Wed Mar 13, 2024 1:06 am - 10 Replies
- 8136 Views
- Last post by DavidR8
Thu Mar 13, 2025 6:15 pm
- UCCNC - Software update or new version
-
- I2R 8 Profile Settings
by shurst77 » Wed Mar 05, 2025 10:03 pm - 8 Replies
- 6261 Views
- Last post by cncdrive
Mon Mar 10, 2025 9:57 pm
- I2R 8 Profile Settings
-
- UCCNC Crash
by Mindustrys » Fri Mar 07, 2025 5:38 pm - 2 Replies
- 1675 Views
- Last post by Mindustrys
Fri Mar 07, 2025 8:17 pm
- UCCNC Crash
-
- Spindle up to speed confirmation
by bhdavis » Tue Aug 20, 2024 2:03 pm - 7 Replies
- 5862 Views
- Last post by valhallaCNC
Thu Mar 06, 2025 10:59 pm
- Spindle up to speed confirmation
-
- Lightburn G Code Error Message on "Cycle Start"
by Loren » Thu Feb 27, 2025 3:37 pm
- 7 Replies
- 14717 Views
- Last post by Loren
Thu Mar 06, 2025 1:35 am
- Lightburn G Code Error Message on "Cycle Start"
-
- Holding power of Stepper motors
by yagodajm » Tue Mar 04, 2025 3:46 pm - 3 Replies
- 2254 Views
- Last post by ger21
Wed Mar 05, 2025 12:23 pm
- Holding power of Stepper motors
-
- Values on the Y-axis and Y2-axis
by lansing » Mon Mar 03, 2025 2:55 pm
- 5 Replies
- 5970 Views
- Last post by cncdrive
Tue Mar 04, 2025 5:25 pm
- Values on the Y-axis and Y2-axis
-
- UCCNC license file not working
by 750ml » Wed Jun 26, 2024 4:12 pm - 6 Replies
- 10922 Views
- Last post by elenagilbert
Tue Mar 04, 2025 2:24 am
- UCCNC license file not working
-
- Saving current Z position into the tool length table.
by zerodivide » Mon Oct 26, 2020 8:18 pm - 8 Replies
- 19092 Views
- Last post by hacker77
Fri Feb 28, 2025 3:12 pm
- Saving current Z position into the tool length table.
-
- Probelt aborts when probe activates during calibration
by vciforge » Wed Feb 26, 2025 2:07 am - 1 Replies
- 4471 Views
- Last post by vciforge
Thu Feb 27, 2025 8:07 am
- Probelt aborts when probe activates during calibration
-
- Probelt not working with probe
by vciforge » Wed Feb 26, 2025 2:06 am - 0 Replies
- 4371 Views
- Last post by vciforge
Wed Feb 26, 2025 2:06 am
- Probelt not working with probe
-
- UCCNC demo mode
by scubalemur » Wed Feb 19, 2025 3:59 am - 2 Replies
- 5321 Views
- Last post by elenagilbert
Thu Feb 20, 2025 7:25 am
- UCCNC demo mode
-
- ucr201 questions
by JerryHorn » Thu Feb 20, 2025 3:04 am - 0 Replies
- 4381 Views
- Last post by JerryHorn
Thu Feb 20, 2025 3:04 am
- ucr201 questions
-
- The solution for jerky movement for Fusion users?
1, 2 by Roby » Wed May 08, 2024 4:47 am
- 14 Replies
- 20897 Views
- Last post by cncdrive
Wed Feb 19, 2025 4:14 pm
- The solution for jerky movement for Fusion users?
-
- OptLasers +UNCNC + UC100 + Stepcraft D840 Issues
by Rossb723 » Sat Dec 21, 2024 11:00 pm - 3 Replies
- 9742 Views
- Last post by sparksgr
Sat Feb 15, 2025 3:16 pm
- OptLasers +UNCNC + UC100 + Stepcraft D840 Issues
-
- How to set Z-probe direction (not in plugin)
by cnconst » Tue Jan 28, 2025 7:51 am - 3 Replies
- 8004 Views
- Last post by alexscott
Sat Feb 15, 2025 1:56 pm
- How to set Z-probe direction (not in plugin)
-
- Homing issue
by rayclark » Mon Feb 10, 2025 4:07 pm - 4 Replies
- 9178 Views
- Last post by elenagilbert
Thu Feb 13, 2025 5:03 am
- Homing issue
-
- Invento cam Postprosessor, how to edit it ????
by Eskolin » Sun Jan 19, 2025 6:19 pm - 2 Replies
- 7894 Views
- Last post by hilosophy
Mon Feb 10, 2025 5:00 am
- Invento cam Postprosessor, how to edit it ????
Who is online
Users browsing this forum: No registered users and 5 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum