General discussion about the UCCNC software
-
- Announcements
- Replies
- Views
- Last post
-
- New USB drivers for UC100
by cncdrive » Tue Mar 04, 2025 4:14 pm
- 9 Replies
- 13399 Views
- Last post by jenniekim
Thu Jun 05, 2025 1:30 am
- New USB drivers for UC100
-
- Topics
- Replies
- Views
- Last post
-
- !!!Fake UC100 controllers on e-bay!!!
1, 2, 3, 4, 5 by cncdrive » Mon Oct 17, 2016 7:04 am
- 46 Replies
- 326154 Views
- Last post by HarryPotter69
Fri Feb 02, 2024 2:03 pm
- !!!Fake UC100 controllers on e-bay!!!
-
- Mini PC
by eddienel10 » Tue Jul 15, 2025 7:18 am - 1 Replies
- 35 Views
- Last post by formantjim
Tue Jul 15, 2025 2:00 pm
- Mini PC
-
- Can geodata be used with UCCNC software?
by Laura43 » Mon Jul 14, 2025 10:18 pm - 0 Replies
- 17 Views
- Last post by Laura43
Mon Jul 14, 2025 10:18 pm
- Can geodata be used with UCCNC software?
-
- estimated program run
by austinlau92 » Thu Jul 10, 2025 4:29 am - 1 Replies
- 225 Views
- Last post by cncdrive
Thu Jul 10, 2025 7:43 pm
- estimated program run
-
- Lathe Documentation
by Delco » Tue Jul 01, 2025 6:43 am - 6 Replies
- 1006 Views
- Last post by Delco
Sun Jul 06, 2025 7:57 am
- Lathe Documentation
-
- Uccnc, AXBB-E and VFD
by pspyve » Sat Jun 28, 2025 7:28 am
- 5 Replies
- 609 Views
- Last post by pspyve
Sat Jul 05, 2025 11:32 am
- Uccnc, AXBB-E and VFD
-
- THC-3 Screenset Problem
by itsbrokeagain » Thu Jul 03, 2025 2:52 pm - 0 Replies
- 409 Views
- Last post by itsbrokeagain
Thu Jul 03, 2025 2:52 pm
- THC-3 Screenset Problem
-
- Why does the motion planner not make use of b-splines?
by aethersis » Wed Jun 25, 2025 12:15 pm
- 8 Replies
- 871 Views
- Last post by cncdrive
Sun Jun 29, 2025 7:45 pm
- Why does the motion planner not make use of b-splines?
-
- UCCNC Tangential knife setup
by Ggfr » Thu Apr 17, 2025 4:58 pm
- 6 Replies
- 2983 Views
- Last post by jimpointoh
Sat Jun 28, 2025 7:50 pm
- UCCNC Tangential knife setup
-
- Safety door check
by odino87 » Thu Nov 28, 2024 10:40 am - 6 Replies
- 4292 Views
- Last post by odino87
Fri Jun 27, 2025 2:35 pm
- Safety door check
-
- AXBB-E losing drive control
by James Frost Electro » Mon Jun 23, 2025 12:36 pm - 4 Replies
- 492 Views
- Last post by rvalotta
Tue Jun 24, 2025 4:25 pm
- AXBB-E losing drive control
-
- ConnectionAliveSignal?
by Optimalisten » Sat Jun 14, 2025 6:49 pm - 4 Replies
- 4143 Views
- Last post by Optimalisten
Fri Jun 20, 2025 4:06 pm
- ConnectionAliveSignal?
-
- Firmware updates?
by Optimalisten » Fri Jun 06, 2025 5:31 pm - 4 Replies
- 3854 Views
- Last post by cncdrive
Sat Jun 07, 2025 7:16 pm
- Firmware updates?
-
- UCCNC Z Drops! Help
by tahoedirk » Wed Jun 04, 2025 7:19 pm - 3 Replies
- 1641 Views
- Last post by tahoedirk
Sat Jun 07, 2025 4:34 pm
- UCCNC Z Drops! Help
-
- .0001 inch jog for MPG wheel
by Malandkamer » Mon May 19, 2025 3:27 pm - 2 Replies
- 1657 Views
- Last post by Malandkamer
Thu Jun 05, 2025 12:56 pm
- .0001 inch jog for MPG wheel
-
- lathe toolprobe
by Delco » Tue Jun 03, 2025 12:18 pm - 0 Replies
- 1955 Views
- Last post by Delco
Tue Jun 03, 2025 12:18 pm
- lathe toolprobe
-
- Setting up a lathe with gearbox.
by Delco » Mon May 19, 2025 11:55 am - 1 Replies
- 1262 Views
- Last post by cncdrive
Tue May 20, 2025 6:09 am
- Setting up a lathe with gearbox.
-
- I2R 8 Profile Settings
1, 2by shurst77 » Wed Mar 05, 2025 10:03 pm - 10 Replies
- 12702 Views
- Last post by cncdrive
Sat May 10, 2025 2:42 pm
- I2R 8 Profile Settings
-
- Lightburn G Code Error Message on "Cycle Start"
by Loren » Thu Feb 27, 2025 3:37 pm
- 8 Replies
- 19094 Views
- Last post by elenagilbert
Tue May 06, 2025 8:09 am
- Lightburn G Code Error Message on "Cycle Start"
-
- Transfer UCCNC licence
by DavidR8 » Mon May 05, 2025 9:39 pm - 1 Replies
- 1336 Views
- Last post by DavidR8
Mon May 05, 2025 10:31 pm
- Transfer UCCNC licence
-
- Juddery corner issue
by jsobell » Tue Apr 22, 2025 1:24 pm - 1 Replies
- 6989 Views
- Last post by ger21
Tue Apr 22, 2025 4:24 pm
- Juddery corner issue
Who is online
Users browsing this forum: Bing [Bot] and 4 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum