General discussion about the UCCNC software
-
- Announcements
- Replies
- Views
- Last post
-
- New USB drivers for UC100
by cncdrive » Tue Mar 04, 2025 4:14 pm
- 9 Replies
- 11877 Views
- Last post by jenniekim
Thu Jun 05, 2025 1:30 am
- New USB drivers for UC100
-
- Topics
- Replies
- Views
- Last post
-
- !!!Fake UC100 controllers on e-bay!!!
1, 2, 3, 4, 5 by cncdrive » Mon Oct 17, 2016 7:04 am
- 46 Replies
- 321831 Views
- Last post by HarryPotter69
Fri Feb 02, 2024 2:03 pm
- !!!Fake UC100 controllers on e-bay!!!
-
- ConnectionAliveSignal?
by Optimalisten » Sat Jun 14, 2025 6:49 pm - 1 Replies
- 177 Views
- Last post by ger21
Sun Jun 15, 2025 4:40 pm
- ConnectionAliveSignal?
-
- Firmware updates?
by Optimalisten » Fri Jun 06, 2025 5:31 pm - 4 Replies
- 3029 Views
- Last post by cncdrive
Sat Jun 07, 2025 7:16 pm
- Firmware updates?
-
- UCCNC Z Drops! Help
by tahoedirk » Wed Jun 04, 2025 7:19 pm - 3 Replies
- 858 Views
- Last post by tahoedirk
Sat Jun 07, 2025 4:34 pm
- UCCNC Z Drops! Help
-
- .0001 inch jog for MPG wheel
by Malandkamer » Mon May 19, 2025 3:27 pm - 2 Replies
- 923 Views
- Last post by Malandkamer
Thu Jun 05, 2025 12:56 pm
- .0001 inch jog for MPG wheel
-
- lathe toolprobe
by Delco » Tue Jun 03, 2025 12:18 pm - 0 Replies
- 780 Views
- Last post by Delco
Tue Jun 03, 2025 12:18 pm
- lathe toolprobe
-
- Setting up a lathe with gearbox.
by Delco » Mon May 19, 2025 11:55 am - 1 Replies
- 596 Views
- Last post by cncdrive
Tue May 20, 2025 6:09 am
- Setting up a lathe with gearbox.
-
- I2R 8 Profile Settings
1, 2by shurst77 » Wed Mar 05, 2025 10:03 pm - 10 Replies
- 10914 Views
- Last post by cncdrive
Sat May 10, 2025 2:42 pm
- I2R 8 Profile Settings
-
- Lightburn G Code Error Message on "Cycle Start"
by Loren » Thu Feb 27, 2025 3:37 pm
- 8 Replies
- 18019 Views
- Last post by elenagilbert
Tue May 06, 2025 8:09 am
- Lightburn G Code Error Message on "Cycle Start"
-
- Transfer UCCNC licence
by DavidR8 » Mon May 05, 2025 9:39 pm - 1 Replies
- 680 Views
- Last post by DavidR8
Mon May 05, 2025 10:31 pm
- Transfer UCCNC licence
-
- Juddery corner issue
by jsobell » Tue Apr 22, 2025 1:24 pm - 1 Replies
- 6357 Views
- Last post by ger21
Tue Apr 22, 2025 4:24 pm
- Juddery corner issue
-
- UCCNC Tangential knife setup
by Ggfr » Thu Apr 17, 2025 4:58 pm
- 3 Replies
- 2041 Views
- Last post by elenagilbert
Sat Apr 19, 2025 1:19 am
- UCCNC Tangential knife setup
-
- Probe Gage Height not respected after switching to 1.2117
by Dale » Sat Mar 22, 2025 4:40 pm
- 2 Replies
- 2400 Views
- Last post by sabrina23
Thu Apr 17, 2025 4:27 am
- Probe Gage Height not respected after switching to 1.2117
-
- Am I do someting wrong with tool measuring?
1, 2by bhdavis » Thu Apr 03, 2025 11:13 pm - 18 Replies
- 7078 Views
- Last post by bhdavis
Tue Apr 15, 2025 12:02 pm
- Am I do someting wrong with tool measuring?
-
- Reset Message disable
by kucharzb » Wed Apr 09, 2025 2:37 pm - 1 Replies
- 2107 Views
- Last post by cncdrive
Fri Apr 11, 2025 12:31 am
- Reset Message disable
-
- Custom sliders for custom screenset
by iOne » Thu Apr 03, 2025 4:12 am
- 1 Replies
- 2057 Views
- Last post by cncdrive
Thu Apr 03, 2025 6:34 pm
- Custom sliders for custom screenset
-
- Can the "Codeview" object read more lines of code?
1, 2 by iOne » Sun Mar 30, 2025 9:28 am
- 12 Replies
- 4427 Views
- Last post by cncdrive
Tue Apr 01, 2025 2:34 am
- Can the "Codeview" object read more lines of code?
-
- UCCNC Crash
by Mindustrys » Fri Mar 07, 2025 5:38 pm - 4 Replies
- 4133 Views
- Last post by hilosophy
Mon Mar 31, 2025 4:45 am
- UCCNC Crash
-
- Modbus Master Plugin Recommendations
by iOne » Sun Mar 30, 2025 9:51 am - 1 Replies
- 2061 Views
- Last post by cncdrive
Sun Mar 30, 2025 11:47 pm
- Modbus Master Plugin Recommendations
-
- UCCNC releases testing only?
by DavidR8 » Mon Mar 24, 2025 4:29 pm - 6 Replies
- 2932 Views
- Last post by cncdrive
Thu Mar 27, 2025 12:31 am
- UCCNC releases testing only?
Who is online
Users browsing this forum: No registered users and 3 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum