This Section is for users to discuss hardware
-
- Faster controller for high count servos?.
by Dazp1976 » Sat May 21, 2022 5:28 pm
- 3 Replies
- 2483 Views
- Last post by cncdrive
Mon May 23, 2022 7:51 am
-
- DG4S firmware update woes
by atomic » Sat May 07, 2022 8:39 pm
- 4 Replies
- 2916 Views
- Last post by atomic
Thu May 12, 2022 4:09 am
-
- UC300ETH 5LPT looses connection
by skovnesky » Tue May 10, 2022 12:58 am
- 2 Replies
- 2050 Views
- Last post by skovnesky
Wed May 11, 2022 12:05 am
-
- Uc300eth-5ltp VFD Wiring
by kiark » Sat Apr 23, 2022 7:36 pm
- 16 Replies
- 11764 Views
- Last post by kiark
Tue May 03, 2022 12:35 pm
-
- Auxiliary (24V in schematic) always on?
by davida1234 » Sun May 01, 2022 3:30 pm
- 1 Replies
- 1736 Views
- Last post by ger21
Sun May 01, 2022 3:48 pm
-
- So... how does this ethernet connection work?
by muzzlitebeer » Mon Apr 18, 2022 2:08 pm
- 5 Replies
- 3349 Views
- Last post by Dazp1976
Fri Apr 29, 2022 5:01 pm
-
- Is anyone here familiar with a Folinn BD600 VFD?
by muzzlitebeer » Fri Apr 29, 2022 7:12 am
- 0 Replies
- 1557 Views
- Last post by muzzlitebeer
Fri Apr 29, 2022 7:12 am
-
- AXBB-E and solenoids
by nitro » Thu Apr 21, 2022 1:45 pm
- 3 Replies
- 2649 Views
- Last post by nitro
Mon Apr 25, 2022 1:56 pm
-
- AXBB-E and CL57Y Closed Loop Stepper Drives
by redwingsfan71 » Tue Apr 19, 2022 4:07 am
- 3 Replies
- 2733 Views
- Last post by redwingsfan71
Tue Apr 19, 2022 2:11 pm
-
- wiring probe with led
by Morfeus80 » Sun Mar 13, 2022 9:08 pm
- 1 Replies
- 1975 Views
- Last post by twedlake
Wed Apr 06, 2022 12:39 pm
-
- Powering a uc300eth
by jesus638 » Mon Apr 04, 2022 1:19 am
- 3 Replies
- 2738 Views
- Last post by jesus638
Mon Apr 04, 2022 8:55 pm
-
- UCSB breakout board with UC300ETH 5LPT
by skovnesky » Mon Mar 21, 2022 11:41 pm
- 5 Replies
- 3721 Views
- Last post by skovnesky
Fri Apr 01, 2022 11:17 pm
-
- How to choose with motion controller and breakoutboard?
by mikkokui » Tue Mar 22, 2022 11:53 am
- 2 Replies
- 2467 Views
- Last post by Dazp1976
Sat Mar 26, 2022 12:38 am
-
- UC300ETH-5LPT port 4,5 as standard port.
by johu » Fri Jan 08, 2021 4:08 pm
- 7 Replies
- 6985 Views
- Last post by Dazp1976
Sat Mar 26, 2022 12:24 am
-
- New builder looking for Motion control recommendation
by Muddi1 » Tue Mar 08, 2022 5:51 am
- 4 Replies
- 3409 Views
- Last post by Dazp1976
Thu Mar 24, 2022 6:48 pm
-
- UC300ETH & UCCNC v1. 2113. Input #15 shown as output????
by Dazp1976 » Wed Mar 16, 2022 1:27 pm
- 2 Replies
- 2315 Views
- Last post by Dazp1976
Thu Mar 24, 2022 6:27 pm
-
- AXBB Unable To Output Full 10v With VFD
by KLewtak » Wed Mar 20, 2019 8:16 pm
- 16 Replies
- 24290 Views
- Last post by wattstar
Wed Mar 16, 2022 2:02 am
-
- Triggers to drive a light tower.
by spillage » Thu Mar 10, 2022 2:15 am
- 0 Replies
- 1642 Views
- Last post by spillage
Thu Mar 10, 2022 2:15 am
-
- Probe causing circuit breaker
by Jason1970 » Mon Mar 07, 2022 3:19 pm
- 4 Replies
- 3123 Views
- Last post by Jason1970
Wed Mar 09, 2022 11:28 pm
-
- UC100 no green light
by Nadalxn » Sun Feb 27, 2022 5:03 am
- 4 Replies
- 3279 Views
- Last post by cncdrive
Wed Mar 02, 2022 12:54 pm
-
- UC300ETH Pinout
by mb300sd » Thu Feb 24, 2022 6:51 am
- 1 Replies
- 1959 Views
- Last post by dezsoe
Thu Feb 24, 2022 1:07 pm
-
- Limit switch wiring confusion
by DavidR8 » Mon Feb 21, 2022 5:02 pm
- 5 Replies
- 3735 Views
- Last post by DavidR8
Tue Feb 22, 2022 2:38 am
-
- Power for AXBB
by DavidR8 » Wed Feb 16, 2022 6:02 am
- 5 Replies
- 3816 Views
- Last post by DavidR8
Thu Feb 17, 2022 10:29 pm
-
- UCCNC 300ETH and RS485 Modbus Network problem
by kucharzb » Mon Feb 07, 2022 3:59 pm
- 4 Replies
- 3370 Views
- Last post by dezsoe
Mon Feb 07, 2022 10:47 pm
-
- UC100 seems to have failed
by scsmith1451 » Fri Feb 04, 2022 9:56 pm
- 5 Replies
- 3731 Views
- Last post by cncdrive
Sun Feb 06, 2022 2:12 pm
Return to Board index
Who is online
Users browsing this forum: No registered users and 9 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum